Fretting wearBRADY, B. G.SAE transactions. 1990, Vol 99, Num 1, pp 1344-1360, issn 0096-736X, 1Article

Verschleiss von Kontruktionswerkstoffen durch Abrasiv-Strahlen hoher Geschwindigkeit = Wear of structural materials by high-speed abrasive blastingMOMBER, A.Schmierungstechnik. 1991, Num 5, pp 132-135, issn 0036-6226Article

Wear by abrasives: methodology and results of investigationsSOROKIN, G. M; GRIGORYEV, S. P; SAPHONOV, B. P et al.Tribology international. 1991, Vol 24, Num 1, pp 3-9, issn 0301-679XArticle

Wear and lubrication as observed on a lap table with loose and bonded abrasive gritABRAHAMSON, G. R; DUWELL, E. J; MCDONALD, W. J et al.Journal of tribology. 1991, Vol 113, Num 2, pp 249-254, issn 0742-4787Article

Abrasion-resistant parts for cat crackers. Experience in manufacture and operationDENISOV, D. E; ZHIDKOV, A. B; VLASOV, V. V et al.Chemistry and technology of fuels and oils. 2003, Vol 39, Num 5, pp 247-252, issn 0009-3092, 6 p.Article

Mechanism of material removal under high stress abrasive wear conditions under varying experimental conditionsDASGUPTA, R; MODI, O. P; YADAV, M. S et al.Journal of materials science letters. 2001, Vol 20, Num 20, pp 1837-1839, issn 0261-8028Article

Effects of dislodgment and size of abrasive grains on abrasive wearHISAKADO, T; SUDA, H; TSUKUI, T et al.Wear. 1992, Vol 155, Num 2, pp 297-307, issn 0043-1648Article

The transformation of soft-abrasive wear into hard-abrasive wear under the effect of frictional heatNING WANG.Tribology transactions. 1989, Vol 32, Num 1, pp 85-90, issn 1040-2004, 6 p.Article

Development of a prototype abrasive wear tester for tillage tool materialsYU, H.-J; BHOLE, S. D.Tribology international. 1990, Vol 23, Num 5, pp 309-316, issn 0301-679X, 8 p.Article

Effects of modification and heat-treatment on the abrasive wear behavior of hypereutectic Al-Si alloysXU, C. L; YANG, Y. F; WANG, H. Y et al.Journal of materials science. 2007, Vol 42, Num 15, pp 6331-6338, issn 0022-2461, 8 p.Article

Dome valves solve problem at blue circle's Westbury worksGREENWOOD, G.World cement. 1995, pp 56-58, issn 0263-6050, 2 p., NSArticle

Free-abrasive wear of an enamel coatingJIN TONG; ZHANG, M.-Z; MAN JIANG et al.Journal of materials science letters. 1998, Vol 17, Num 6, pp 523-525, issn 0261-8028Article

A study of the abrasive wear of carbon steelsLIQUN XU; KENNON, N. F.Wear. 1991, Vol 148, Num 1, pp 101-112, issn 0043-1648Article

Usure par abrasion: possibilités d'amélioration. Exemples = Abrasive wear, improvement possibilities: examplesDE LA RUPELLE, G.Ciments, bétons, plâtres, chaux. 1990, Num 1, pp 53-56, issn 0397-006XArticle

Instandhaltung von Dampfturbinen-Endstufenschaufeln = Maintenance of steam turbine end-stage bladesSTORCH, W; MOSSAKOWSKI, G; MEHLHORN, J et al.Brennstoff-Wärme-Kraft. 1993, Vol 45, Num 5, pp 240-246, issn 0006-9612, 270 [8 p.]Article

Lubrication of gears. IIERRICHELLO, R.Lubrication engineering. 1990, Vol 46, Num 2, pp 117-121, issn 0024-7154, 5 p.Article

Nanoeffekte bei Reibung und Verschleiss = Nano-effects of friction and wearSCHERGE, M; SHAKHVOROSTOV, D; PÖHLMANN, K et al.Erdöl, Erdgas, Kohle. 2004, Vol 120, Num 2, pp 76-80, issn 0179-3187, 5 p.Conference Paper

The effect of grit size and asperity blunting on abrasive wearTORRANCE, A. A.Wear. 2002, Vol 253, Num 7-8, pp 813-819, issn 0043-1648, 7 p.Article

Six strategies for combating abrasion in your low-speed blender : Part IFEIBERT, H; PURSE, B.Powder and bulk engineering. 2000, Vol 14, Num 6, pp 19-24, issn 0897-6627, 3 p.Article

Fabric abrasion as a function of fabric life and filler contentHEGER, W.Paper technology (1989). 1998, Vol 39, Num 1, pp 31-37, issn 0958-6024Conference Paper

Abrasivverschleiss durch Äquivalent-Härte Kennzeichnen = Equivalent hardness and abrasive wear behaviour of ferrous alloysAL-RUBAIE, K. S; POHL, M.Materialprüfung. 1997, Vol 39, Num 3, pp 86-90, issn 0025-5300Article

Standzeitverhalten von Schleifwerkzeugen beim Schleifen von Fichte = Wear of sanding tools during machining of spruceWESTKÄMPER, E; RIEGEL, A.Holz als Roh- und Werkstoff. 1995, Vol 53, Num 5, pp 281-287, issn 0018-3768Article

The abrasion resistance of sewers. IJÄRVENKYLÄ, J. J; HAAVISTO, K. T.Pipes & pipelines international (1965). 1993, Vol 38, Num 5, pp 34-40, issn 0032-020XArticle

Effect of nonylpolysulphide in different base oils on abrasive belt grinding of stainless steelNAKAYAMA, M; KUDO, K; HIROSE, T et al.Tribology international. 1989, Vol 22, Num 6, pp 389-393, issn 0301-679X, 5 p.Article

Effect of indentation size and microhardness calculation on abrasive wear severityPINTAUDE, G; TANAKA, D. K; SINATORA, A et al.Scripta materialia. 2001, Vol 44, Num 4, pp 659-663, issn 1359-6462Article